Due: 2:00 p.m. before your next lab section.
- Lab Log: Keep a complete lab log: circuit diagrams, measurements, analysis steps, and observations. Include clear photographs of instrument readings and circuit setups.
- Report Format: Submit a typed lab report in PDF format. Hand-drawn circuit diagrams will not be accepted; draw every schematic with software (see Software at the end of this manual).
- Time: Plan your time. Makeup sessions are available by appointment with your TA, subject to their availability.
- AI Policy: The use of any AI tool, including a large language model (LLM), to write, generate, debug, or modify code or any portion of the lab report is prohibited unless the course instructor grants explicit permission in advance. A teaching assistant (TA) cannot grant permission to use AI tools.
By signing below, I acknowledge that I have read and understood the policies and instructions above and agree to follow them.
Student Name (print):
Student Signature: Date:
All tasks in this lab are required. The Lecture 01 notes cover the tools and the methods you need.
Prototyping Station and Basic Measurements
Task 1: Station Familiarization
Learn the essential parts of the prototyping station from your professor:
- Breadboard zones and power rails.
- Integrated and external power supplies, and how they compare.
- Proper grounding, and the common mistakes.
Course Instructor or TA Signature:
Date and Time:
Task 2: Precision Measurements
Use a digital multimeter (DMM) to measure:
- One resistor in the 470 Ω range (standard value).
- One resistor in the 22 kΩ range (standard value).
- One resistor in the 2.2 MΩ range (standard value).
Calculate the percentage deviation of each from its nominal value, and compare it with the resistor's tolerance band. Keep these resistors for Task 4.
Course Instructor or TA Signature:
Date and Time:
Power Distribution Design
Task 3: USB Power Distribution
Design and build a voltage divider network that gives these common voltage levels from a 12 V input:
- 5 V (USB standard)
- 3.3 V (logic level)
- 1.8 V (low-power devices)
Use resistors of 2.2 kΩ or more to limit the current draw. Document your design process and your calculations, and include the schematic.
Course Instructor or TA Signature:
Date and Time:
Task 4: Load Effects
Build a voltage divider from two 22 kΩ resistors, then:
- Measure the unloaded output voltage.
- Connect each resistor from Task 2 in turn as the load.
- Record the voltage changes and analyze them.
- Calculate the loading effect, in percent, for each load.
Course Instructor or TA Signature:
Date and Time:
Signal Analysis
Task 5: Waveform Analysis
Set up the oscilloscope to analyze the function generator output on Channel 2:
- Set up the triggering for a stable 1 kHz sine wave.
- Measure and record:
- the frequency accuracy (expected against measured),
- the period, to microsecond precision,
- the peak-to-peak voltage (500 mV target).
- Export the waveform data to your USB drive.
- Make a simple plot of your captured waveform.
Course Instructor or TA Signature:
Date and Time:
Submission Reminder
- Your lab log notes and photographs of the instrument readings and the circuits.
- Task 2: the three measured values, their percentage deviations, and the comparison with each tolerance band.
- Task 3: the schematic, your design calculations, and the measured output voltages.
- Task 4: the unloaded and loaded output voltages and the loading effect for each load.
- Task 5: the measured frequency, period and peak-to-peak voltage, and the plot of your exported waveform.
- An error analysis for every task where it applies: the uncertainty of each measured or calculated value, its main sources of error, and a comparison with the expected, simulated, or datasheet value.
- A discussion of any challenges you met and how you solved them.
Draw every circuit diagram with software; hand-drawn circuit diagrams will not be accepted. We recommend the free draw.io; the course’s Drawing Circuit Diagrams page shows how to set it up. If a component has no symbol of its own, use the closest one and label it clearly.
Where a task asks for a simulation: the web version of Multisim is no longer available. If you have a Windows computer, you can install the offline (desktop) version of Multisim; ask a TA for the serial number to install it. Otherwise, feel free to use any SPICE-based simulation tool, such as LTspice or ngspice.