← About PHYS 252

PHYS 252 · Electronics

Lab 3 · Capacitors & RC filters

Submission Submit the completed lab report as a PDF on Gradescope.

Due: 2:00 p.m. before your next lab section.

Policies and Instructions
  1. Lab Log: Keep a complete lab log: circuit diagrams, measurements, analysis steps, and observations. Include clear photographs of instrument readings and circuit setups.
  2. Report Format: Submit a typed lab report in PDF format. Hand-drawn circuit diagrams will not be accepted; draw every schematic with software (see Software at the end of this manual).
  3. Time: Plan your time. Makeup sessions are available by appointment with your TA, subject to their availability.
  4. AI Policy: The use of any AI tool, including a large language model (LLM), to write, generate, debug, or modify code or any portion of the lab report is prohibited unless the course instructor grants explicit permission in advance. A teaching assistant (TA) cannot grant permission to use AI tools.

By signing below, I acknowledge that I have read and understood the policies and instructions above and agree to follow them.

Student Name (print):

Student Signature: Date:

All tasks in this lab are required. The Lecture 03 notes cover capacitors, impedance, RC filters and the measuring methods you need.

Complex Impedance

Task 1

Use a DMM to measure the capacitance of:

  1. One electrolytic capacitor rated at 100 µF.
  2. One ceramic capacitor rated at 0.1 µF.
  3. One ceramic capacitor rated at 0.01 µF.

Compare polarized and unpolarized capacitors. Calculate the reactance of each capacitor at 100 Hz and at 100 kHz.

Task approvalTask 1 (Complex Impedance)

Course Instructor or TA Signature:

Date and Time:

RC Filter Design

Task 2

Design and build a high-pass filter on the breadboard with a cutoff frequency fcf_c between 200 Hz and 2 kHz. Calculate the fcf_c of your filter.

Connect a signal generator to provide the input:

  • Frequency: ff = 20 Hz
  • Amplitude: 500 mV peak to peak

Connect the input to Channel 1 and the output to Channel 2 of the oscilloscope. Measure the peak-to-peak value of the output voltage. Make sure the triggering is stable, and save the waveform. Compare your measurements with your calculations.

Task approvalTask 2 (RC Filter Design)

Course Instructor or TA Signature:

Date and Time:

Frequency Response

Task 3

With an input signal of 500 mV peak to peak, measure the cutoff frequency fcf_c of your filter. Compare it with your calculation.

Calculate:

  • the voltage gain AVA_V at cutoff,
  • the decibel voltage gain AVdBA_{V\text{dB}} at cutoff.

Save the waveform that shows your measurements.

Task approvalTask 3 (Frequency Response)

Course Instructor or TA Signature:

Date and Time:

Phase Analysis

Task 4

Measure the phase angle θ\theta at the fcf_c you found in Task 3, with an input signal of 500 mV peak to peak. Compare your measured result with your calculation and simulation. Save the waveform.

Task approvalTask 4 (Phase Analysis)

Course Instructor or TA Signature:

Date and Time:

Bode Plot Construction

Task 5

Keep the input signal at 500 mV peak to peak. Measure the peak-to-peak value of the output voltage at these frequencies:

  • fc/10f_c/10
  • fc/5f_c/5
  • fc/2f_c/2
  • fcf_c
  • 2fc2f_c
  • 5fc5f_c
  • 10fc10f_c

Save all the waveforms. Make a Bode plot with your measurements.

Task approvalTask 5 (Bode Plot Construction)

Course Instructor or TA Signature:

Date and Time:

Submission Reminder

  1. Your lab log notes and photographs of the instrument readings and the circuits.
  2. Task 1: the three measured capacitances, your comparison of polarized and unpolarized capacitors, and the reactance of each capacitor at 100 Hz and 100 kHz.
  3. Task 2: the schematic, your calculated fcf_c, the saved waveform, and the measured peak-to-peak output voltage compared with your calculation.
  4. Task 3: the measured fcf_c compared with your calculation, AVA_V and AVdBA_{V\text{dB}} at cutoff, and the saved waveform.
  5. Task 4: the measured phase angle at fcf_c compared with your calculation and simulation, and the saved waveform.
  6. Task 5: the peak-to-peak output voltages at the seven frequencies, the saved waveforms, and your Bode plot.
  7. An error analysis for every task where it applies: the uncertainty of each measured or calculated value, its main sources of error, and a comparison with the expected, simulated, or datasheet value.
  8. A discussion of any challenges you met and how you solved them.
Software for drawing and simulation

Draw every circuit diagram with software; hand-drawn circuit diagrams will not be accepted. We recommend the free draw.io; the course’s Drawing Circuit Diagrams page shows how to set it up. If a component has no symbol of its own, use the closest one and label it clearly.

Where a task asks for a simulation: the web version of Multisim is no longer available. If you have a Windows computer, you can install the offline (desktop) version of Multisim; ask a TA for the serial number to install it. Otherwise, feel free to use any SPICE-based simulation tool, such as LTspice or ngspice.

← All course materials