← About PHYS 252

PHYS 252 · Electronics

Lab 5 · BJT characterization & biasing

Submission Submit the completed lab report as a PDF on Gradescope.

Due: 2:00 p.m. before your next lab section.

Policies and Instructions
  1. Lab Log: Keep a complete lab log: circuit diagrams, measurements, analysis steps, and observations. Include clear photographs of instrument readings and circuit setups.
  2. Report Format: Submit a typed lab report in PDF format. Hand-drawn circuit diagrams will not be accepted; draw every schematic with software (see Software at the end of this manual).
  3. Time: Plan your time. Makeup sessions are available by appointment with your TA, subject to their availability.
  4. AI Policy: The use of any AI tool, including a large language model (LLM), to write, generate, debug, or modify code or any portion of the lab report is prohibited unless the course instructor grants explicit permission in advance. A teaching assistant (TA) cannot grant permission to use AI tools.

By signing below, I acknowledge that I have read and understood the policies and instructions above and agree to follow them.

Student Name (print):

Student Signature: Date:

All tasks in this lab are required. The Lecture 05 notes cover the transistor, the DMM test, biasing and the measurement methods you need.

BJT Terminal Identification

Task 1

Using a DMM in diode test mode, complete the following table:

BJT junction measurements
+−2N39042N3906
BC
BE
CE
CB
EB
EC
Task approvalTask 1 (BJT Terminal Identification)

Course Instructor or TA Signature:

Date and Time:

Voltage Divider Bias

Task 2

Build the biasing circuit designed in your homework:

  • Measure and record each resistor value.
  • Verify the transistor's orientation.
  • Set VCC=12V_{CC} = 12 V using the power supply.
  • Measure the DC voltages VBV_B, VEV_E and VCV_C.
Task approvalTask 2 (Voltage Divider Bias)

Course Instructor or TA Signature:

Date and Time:

Current Measurements

Task 3

Make current measurements in your circuit:

  • Measure IEI_E using the voltage across RER_E.
  • Measure ICI_C using the voltage across RCR_C.
  • Calculate IBI_B from your measurements.
  • Determine the actual βdc\beta_{dc}.
  • Compare it with the datasheet specifications (onsemi 2N3904 datasheet).

A tip for IBI_B: it is a small difference of two large currents, so IE−ICI_E - I_C carries a large error. You can also measure IBI_B directly with the DMM's µA range in series with the base.

Task approvalTask 3 (Current Measurements)

Course Instructor or TA Signature:

Date and Time:

Operating Point Verification

Task 4

Analyze the operating point:

  • Calculate VCEV_{CE} from your measurements.
  • Verify that the transistor is in the active region.
  • Compare the actual values with your design targets.
  • Document any discrepancies.
Task approvalTask 4 (Operating Point Verification)

Course Instructor or TA Signature:

Date and Time:

Temperature Effects

Task 5

Observe temperature effects:

  • Record the initial operating point values.
  • Gently warm the transistor with your fingertip.
  • Observe the changes in VCEV_{CE} and ICI_C.
  • Calculate the temperature coefficient.
  • Explain your observations.
Task approvalTask 5 (Temperature Effects)

Course Instructor or TA Signature:

Date and Time:

Submission Reminder

  1. Your lab log notes and photographs of the instrument readings and the circuits.
  2. Task 1: the completed junction table for both transistors, and which lead is the base, collector and emitter of each.
  3. Task 2: the schematic with your design values, the measured resistor values, and the measured VBV_B, VEV_E and VCV_C.
  4. Task 3: IEI_E, ICI_C, IBI_B and βdc\beta_{dc}, with your calculations, and the comparison with the datasheet.
  5. Task 4: VCEV_{CE}, your active-region check, and the comparison with your design targets.
  6. Task 5: the operating point before and while warming, the temperature coefficient with its units, and your explanation.
  7. An error analysis for every task where it applies: the uncertainty of each measured or calculated value, its main sources of error, and a comparison with the expected, simulated, or datasheet value.
  8. A discussion of any challenges you met and how you solved them.
Software for drawing and simulation

Draw every circuit diagram with software; hand-drawn circuit diagrams will not be accepted. We recommend the free draw.io; the course’s Drawing Circuit Diagrams page shows how to set it up. If a component has no symbol of its own, use the closest one and label it clearly.

Where a task asks for a simulation: the web version of Multisim is no longer available. If you have a Windows computer, you can install the offline (desktop) version of Multisim; ask a TA for the serial number to install it. Otherwise, feel free to use any SPICE-based simulation tool, such as LTspice or ngspice.

← All course materials